prev next

POLK 5 CHANNEL AMPLIFIER

Availability:

Brand

Availability: In stock

$799.00
Qty:

Polk 5 Channel Amplifier

Details

Sleek, Compact, Powerful

The PA D5000.5 is capable of bridging two full-range channels into a single full-range channel with higher output power. For instance, the front channels (FL and FR) when wired correctly will increase the output power from 70W per channel to 200W per channel (for a 4 ohm load). The same can be done for the rear channels (RL and RR). The most common configurations are four full-range channels and a subwoofer channel, or two bridged full-range channels and a subwoofer channel.

Features:

  • Super-efficient class D design—runs much cooler than conventional amps.
  • High-speed MOSFET switching—power supply with outputs stable into 2 ohm loads for full range channel speakers and 1 ohm loads for subwoofer channel.
  • Protection—thermal, DC offset, reverse DC voltage and short circuit protection.
  • Sub 1/Sub 2 Inputs—line level inputs for subwoofer signal from head unit
  • SUB/INT source switch—in the INT position, the amplifier will filter the bass frequencies from the full range signal and send them to the subwoofer amplifier channel.
  • SUB sonic filter—attenuates the frequencies below the settings on the control.
  • Remote bass level control—set gain to match output from head unit.
  • Rear Full, HPF switch—selects between no filtering or a high pass filter to dial in your speakers' blending.
  • Channel mode switch (4CH/ST)—in the ST position, the amplifier sends the same signal to the front and rear channels.
  • Nickel-plated wire terminals & RCA connectors—ensure maximum signal transfer.
  • Stainless steel hardware—Used throughout and will not corrode in humid environments.
Technical Specifications
Audio
Amplifier Power Specs RMS Power at 14.4V Watts per channel bridged - 4 ohms 200 x 2 watts
Amplifier Power Specs RMS Power at 14.4V Watts per channel NOT bridged @ 1 kHz - 2 ohms 100 x 4 watts
Amplifier Power Specs RMS Power at 14.4V Watts per channel NOT bridged @ 1 kHz - 4 ohms 70 x 4 watts
Amplifier Specs - 12V & Ground Cable Gauge 4AWG
Amplifier Specs - Channel Notes Bridgeable Class D MOSFET
Amplifier Specs - Channels 5
Amplifier Specs - Power Specs 100W x 4, 400W x 1 RMS @ 2 ohms; 70W x 4, 200W x 1 RMS @ 4 ohms; 200W x 2 RMS bridged @ 4 ohms; 500W x 1 RMS @ 1 ohm (sub)
Dimensions - Product Weight (each) 6.750 lbs. pounds
Dimensions Cabinet Dimensions - Depth 6 3/4 (17.14cm) "
Dimensions Cabinet Dimensions - Height 1 13/16 (4.60cm) "
Dimensions Cabinet Dimensions - Width 13 5/16 (33.81cm) "
Dimensions With Panels - Depth 6 3/4 (17.14cm) "
Dimensions With Panels - Height 1 13/16 (4.60cm) "
Dimensions With Panels - Width 13 5/16 (33.81cm) "
Electrical - Distortion at Rated Power <0.1 %
Electrical - Max Sensitivity 200mV-6V dB
Electrical - Minimum Impedance Bridged 4 ohms
Electrical - Minimum Impedance Not Bridged 2 ohms
Electrical - Protection Circuitry Thermal, DC offset, reverse DC voltage and short circuit; fuses: two 40 Amp ATC
Electrical - Remote Gain yes, for bass
Electrical - Signal-to-noise (Referenced to rated power) 105 dBA
Electrical - Subsonic Filter yes
Electrical - Total Frequency Response 20Hz-20kHz
Electrical High Pass Filter - Filter Frequency 40Hz-400Hz(front)/40Hz-4kHz(rear)
Electrical High Pass Filter - Filter Slope 12dB/octave
Electrical Low Pass Filter - Filter Frequency 80Hz-4kHz(front)

Related Products